Limits Door Opening to 86°
Reduces the hinge opening angle from 105° to approximately 86° to help control cabinet door movement.
A restrictor clip changes the stopping point of a compatible hinge without replacing the entire hinge. This Berta clip is designed for the European / frameless hinge system identified on this product page and reduces a compatible 105° opening to approximately 86°.
The reduced opening range is useful when a cabinet door sits close to a wall, refrigerator, appliance panel or another door. The clip helps stop the door sooner so the handle or door edge is less likely to strike the surrounding surface.
Installation is tool-free: after confirming the exact Berta hinge model, the nylon clip snaps into the hinge and remains mostly concealed during normal use.
This clip is designed specifically for compatible Berta European / frameless hinge systems. It is not universal, does not fit other hinge brands, and is not the correct Berta clip for face-frame hinges.
Berta Store carries two separate 86° restrictor products because frameless / European and face-frame hinge systems use different geometry. Choose the clip by the exact hinge and cabinet construction—not by appearance alone.
For the compatible Berta European-style frameless hinge system identified on this product page.
Use this separate option when the cabinet has a front wood frame and the hinge is the compatible Berta face-frame style.
| Clip Type | Cabinet Construction | Hinge Family | Angle Change | Use This Product? |
|---|---|---|---|---|
| European / Frameless Clip | Cabinet box has no front wood frame | Compatible Berta European-style frameless hinge system | 105° to approximately 86° | Yes — this product |
| Face Frame Clip | Cabinet has a wood frame around the front opening | Compatible Berta face-frame soft-close hinge system | 105° to approximately 86° | Use the face-frame clip |
| Other Brand / Unknown Hinge | Any construction | Non-Berta or unidentified system | Unknown | Do not assume compatibility; identify the hinge first |
Still identifying the cabinet? The Hinge Restrictor Clips collection is the two-product chooser for broad or unspecified restrictor searches.
Use these hinge families to identify and compare Berta frameless hardware. Restrictor compatibility is model-specific, so confirm the exact product-page details or contact Berta Store before adding clips to an existing installation.
Straight-arm full-overlay hinges for modern frameless cabinet doors.
For two frameless doors that share one center cabinet partition.
For compatible frameless doors that sit inside the cabinet opening.
European-style concealed hinge option for frameless cabinets.
Wide-angle full-overlay option for greater frameless cabinet access.
Specialty full-overlay hinge variants for angled frameless cabinet layouts.
The clip installs quickly only after the hinge has been identified correctly. Follow this sequence to avoid ordering the face-frame version or a clip made for another hinge system.
Confirm that the cabinet is frameless: there should be no separate wood frame surrounding the front opening.
Match the existing hinge to the compatible Berta European / frameless system. Brand, arm geometry and model matter more than appearance alone.
With the cabinet door open and supported, insert the nylon restrictor into the designated hinge position. No drilling or screws are required.
Move the door through its range carefully and confirm that it stops before contacting the wall, appliance or neighboring door.
Do not force a clip into a hinge that does not accept it. Send Berta Store clear photos of the hinge, cabinet front and any markings when compatibility is uncertain.
Restrictor clips are most useful in tight layouts where the original hinge swing allows a door or handle to reach a nearby surface.
Limit a door that would otherwise swing into painted drywall, tile, trim or a finished cabinet end panel.
Help reduce contact with refrigerators, range surrounds and other appliance surfaces positioned close to the cabinet run.
Control the swing where two doors, handles or cabinet fronts can collide in a corner or narrow installation.
Use the specification table as an initial check, then verify the exact Berta hinge model before ordering for a replacement installation.
| Specification | Product Detail | Buying Note |
|---|---|---|
| Product Type | Cabinet hinge restrictor clip / opening-angle limiter | Accessory only; hinge is sold separately |
| Opening Angle | Reduces a compatible 105° hinge to approximately 86° | Final movement can depend on the exact hinge and installation |
| Cabinet Construction | Frameless cabinet system | For face-frame cabinets, use the separate face-frame clip |
| Hinge Style | Compatible Berta European-style hinge system | Not universal and not compatible with other brands |
| Material | Nylon | Compact insert remains mostly concealed after installation |
| Installation | Tool-free snap-in installation | Do not force the clip into an unmatched hinge |
| Finish | Unfinished | Hidden within the hinge during normal use |
| Pack Size | 2 restrictor clips | Confirm the required quantity for the specific door and hinge setup |
Use the broad accessory collection when the clip type is unknown, or browse by cabinet construction and hinge function.
It changes the stopping point of a compatible hinge so the cabinet door does not open through its full original range. This clip reduces a compatible 105° Berta hinge to approximately 86°.
No. It is designed specifically for compatible Berta European / frameless hinge systems. It is not made for other brands or unrelated hinge models.
No. Face-frame hinges use a separate restrictor. Choose the 86° Face Frame Hinge Restrictor Clips instead.
No. The clip limits the opening angle; it does not convert a standard hinge into a soft-close hinge. The hinge itself must provide the closing function.
No tools, screws or drilling are required for the compatible hinge. The nylon clip uses a snap-in installation.
Each pack contains two clips. Confirm the number of hinges on the cabinet door and the installation requirements for the exact Berta hinge model.
A smaller swing can help prevent the door edge or handle from reaching a nearby wall, appliance, finished panel or adjacent cabinet door.
Confirm the hinge brand and model first, then identify whether the cabinet is frameless or face frame. When uncertain, compare both options in the Hinge Restrictor Clips collection or send Berta Store product photos.
Send clear photos of the cabinet front, open hinge, mounting plate and any stamped markings. Berta Store can help distinguish the frameless / European clip from the separate face-frame option before you order.